Bosch silver edition dishwasher error codes

Bosch aquastar dishwasher error codes and Bosch dishwasher classixx error codes

bosch silver edition dishwasher error codes

Waste water pump

Large food remnants or foreign objects which were not captured by the filters may block the waste water pump. The rinsing water will then be above the filter.

In this case:

  • First always disconnect the appliance from the power supply.
  • Take out top basket (20) and bottom basket (28).
  • Remove the filters (26).
  • Scoop out water, use a sponge if required.
  • Prise out the white pump cover (as illustrated) using a spoon. Grip the cover on the crosspiece and lift diagonally inwards. Remove cover completely.

Cleaning the pump

  • Check impeller wheel and remove any foreign objects.
  • Place cover in the original position and press down until it engages (click).

Cleaning the pump from the Bosch dishwasher

  • Install filters.
  • Re-insert baskets.

… when the appliance is switched on

The appliance does not start.

  • The mains fuse has tripped.
  • The appliance plug has not been inserted.
  • The appliance door has not been shut properly.

… changing settings

A setting cannot be changed, a programme starts.

  • Wrong programme button pressed. Terminate the programme (see chapter entitled “Terminating the programme (Reset)”) and start all over again.
  • You did not wait until programme ended.

… on the appliance

Lower spray arm rotates sluggishly.

  • Spray arm blocked.

The door is difficult to open.( * depending on model)

  • Child-proof lock is activated. The deactivation instructions are at the back in the envelope.

Door cannot be closed.

  • Door lock has been activated. To reset, close the door with greater force.

Cover on the detergent dispenser cannot be closed.

  • Detergent dispenser overfilled or mechanism blocked by sticky detergent residue.

Detergent residue in the detergent dispenser.

  • Dispenser was damp when filled.

“Check water supply” display (3) lights up.

  • Tap turned off.
  • Water supply interrupted.
  • Supply hose kinked.

Filter in the water supply blocked.

  • Switch off the appliance and pull out the mains plug.
  • Turn off the tap.
  • Clean filter in the supply hose.

Bosch Dishwasher Water Supply Hose Filter

  • Reconnect power supply.
  • Turn on the tap.
  • Switch on the appliance.

Water is left in the appliance at the end of the programme.

  • (E:24) Waste water hose is blocked or kinked. Filters blocked.
  • (E:25) Waste water pump blocked, cover on the waste water pump is not locked in position (see Waste water pump).
  • Filters blocked.
  • The programme has not yet ended. Wait until programme ends (digital display indicates 0:00) or implement the “Reset” function.

Error code E:22

  • Filters (26) are soiled or blocked.

Refill indicator for salt (4) and/or rinse-aid (5) is not lit.

  • Refill indicator/s switched off.
  • Adequate salt/rinse-aid available.

Refill indicator for special salt (4) is lit.

  • No salt. Refill with special salt.
  • Sensor does not detect salt tablets. Use different special salt.

… during the wash cycle

Unusual foam formation.

  • Handwash liquid in the rinse aid dispenser. Spilled rinse aid causes excessive frothing, therefore please remove with a cloth.

Appliance stops during the wash cycle.

  • Power supply interrupted.
  • Water supply interrupted.

Filling valves making striking noises

  • Caused by the installation of the water line and has no effect on the function of the machine. Remedial action is not possible.

Knocking/rattling noise during rinsing

  • Spray arm is striking utensils.
  • Utensils not arranged correctly.

… on the utensils

Food residue on the utensils.

  • Utensils placed too closely together, utensils basket overfilled.
  • Too little detergent.
  • Rinse programme too weak.
  • Spray arm rotation obstructed.
  • Spray arm nozzles blocked.
  • Filters blocked.
  • Filters incorrectly inserted.
  • Waste water pump blocked.
  • Top basket on right and left not set to same height.

Tea or lipstick residue is not completely removed.

  • The detergent has an inadequate bleaching effect.
  • Too low rinsing temperature.
  • Too little/unsuitable detergent.

White stains on the utensils/glasses remain milky.

If phosphate-free detergents are used with hard tap water, white deposits may be deposited more easily on utensils and the container walls.

  • Too little/unsuitable detergent.
  • Too weak programme selected.
  • No/too little rinse aid.
  • No/too little special salt.
  • Water softening system set to the wrong value.
  • Salt dispenser lock not fastened.

Contact the detergent manufacturer, in particular if:

  • the utensils are very wet at the end of the programme.
  • limescale forms.

Dull, discoloured glasses, film cannot be washed off.

  • Unsuitable detergent.
  • Glasses not dishwasher-proof.

Streaks on glasses and cutlery, glasses have metallic appearance.

  • Too much rinse aid.

Plastic parts discoloured.

  • Too little/unsuitable detergent.
  • Too weak programme selected.

Rust spots on the cutlery.

  • Cutlery not rust-resistant.
  • Salt content in the rinsing water too high, as salt dispenser lock not fastened firmly or salt was spilled while being refilled.

Utensils not dry.

  • Appliance door opened too early and utensils taken out too early.
  • Programme selected without drying.
  • Too little/unsuitable rinse aid.
  • Activate intensive drying.
  • The combined detergent used has a poor drying performance. Use rinse aid

Leave a Reply

Your email address will not be published. Required fields are marked *